HIMMEL®-drum motors are used for driving both stationary and mobile conveyor belts to move various types of bulk materials; they are also used in transport systems that do not use belts. The HIMMEL®-drum motor has a space-saving design and good adaptability for varying usage conditions, allowing to be used in ever more different applications. It has already been successfully in use for decades in many areas of conveyor technology. HIMMEL®-drum motors are designed so that the electromotor and reduction gear are housing inside the drum shell, forming a closed gear unit that is well protected against external influences. Good dimensioning of the individual parts guarantees a long service life, even under tough operating conditions. The latest production methods ensure low noise operation with high efficiency. The mutual clamping shafts are flattened and allow for simple and time-saving installation using a two-part clamping point. HIMMEL®-drum motors have an entirely closed design, making them dust-proof and hose-proof up to IP69k. They are therefore suitable for use outdoors and in dusty or damp spaces. Electromagnetic brakes, backstops and rotational speed monitors can be installed. The design principle of HIMMEL®-drum motors ensures low noise and the minimal installation space makes them space-saving drive solutions.

HIMMEL®_ Flat motors have a compact and space-saving design that is ideal for milling, cutting, scoring, boring, sawing, chipping and grinding - in both complex heavy-duty machine systems where demands on the drive unit for operating precision and performance are high, and simple machine systems where an affordable and reliably drive solution is needed. Our flat motors have been design so that they will operate flawlessly, even under the toughest of conditions. The HIMMEL®Flat motor range consists of six different design sizes so that we will always have the right motor for the widest range of usage conditions. Alongside our decades of experience, our motors are under constant development. The latest technology and the specific needs of our customers are what define our products.

HIMMEL®gear motors are used for driving slow running machines. A gear motor is the combination of a motor and a gear unit. The gear unit works to make the drive shaft rotate at a lower speed and higher torque than the motor shaft. For this reason, HIMMEL®gear motors are used where the required output speeds and torques cannot be economically achieved using conventional electric motors. The applications for gear motors are very wide ranging. Primary applications in industry are driving haulageways as well as lifting, lowered and moving loads in various plant systems. The design principle of HIMMEL®gear motors ensures low noise and the minimal installation space makes them space-saving drive solutions. Cast iron housing for stable and low-vibration continuous operating. Some gear unit types can also be supplied with an aluminium housing. All gear wheels are milled, crowned or ground with a hardened surface. Helical gearing of the gear teeth achieves excellent operating smoothness HIMMEL®gear motors are available as foot or flange mounted versions and can be installed in any position using the relevant amount of lubricant. Applications such as the additional installation of electromagnetic brakes, backstops and speed monitors are also possible. No matter what special dimensions you have for the shaft or flange, HIMMEL Antriebstechnik can supply the right drive unit. Our design department is able to develop and deliver exactly the right solution for your drive problem.

A standard repair and exchange solution for your HMI & PLC We repair and test programmable logic controllers and command stations. - Siemens : Simatic S5 : 95 / 100 /115 / 135 / 155 U… Simatic S7 : 200, 300, 400... - SCHNEIDER Electric (Telemecanique) : TSX 17, TSX 47, TSX 37, TSX 57... - ALLEN BRADLEY : SLC 500, Control Logix… - OMRON : CPU 21, CQM 1… - SIEMENS : NANO BOX PC, MICRO BOX PC, RACK PC, PANEL PC, PC LITE Power PG (IL70, IPC4727B, IPC477B, IPC577, IPC670, IPC677, IPC870, IPC877…)

DV GROUP repairs : SIEMENS: Simatic S5: 95 / 100 /115 / 135 / 155 U… Simatic S7: 200, 300, 400, usw. SCHNEIDER ELECTRIC: (Telemechanik) TSX 17, TSX 47, TSX 37, TSX 57, usw. ALLEN BRADLEY: SLC 500, Control Logix, usw. OMRON: CPU 21, CQM 1, usw.

The gentle force in the sewer In the development of the Drain-Jet-Robotics technology for our ultra-high-pressure water jetting robots is the result of 25 years of experience with ultra-high pressure. This enables us to cover a wide range of sewer applications with our technology: - From DN 150 up to and including walkable or DN 1300 (egg profile DN 1000/1500), in special cases from DN 100 or even DN 80. - All standard sewer profiles including numerous special profiles. - Maximum pipe length: 300 metres (by arrangement) Sewer rehabilitation with ultra-high-pressure water jetting robots We have German and international industrial property rights in technology for robot-guided ultra-high-pressure water jetting in sewers. Drain-Jet Robotics® technology is several times faster and therefore more cost-effective than conventional milling robots. Our ultra-high-pressure water jetting robots, specially developed for removing obstructions in sewers robots work with camera support, adjustable water pressure and customisable travel speeds. High-pressure water jet cutting Our environmentally friendly cold cutting process has proven itself time and time again, especially in hazardous areas. hazardous areas. Even the hardest materials, including sandwich constructions, can be cut easily and without heat input. Another important deciding factor is the mobility of the technology and the fact that it can be used in the most different locations - even under water.

Hose pump

Twinline High Pressure Hydraulic Hoses - Available hoses range 15ft to 50ft. Longer hoses can be special ordered.

Our knowledge of Heat Recovery Steam Generators (HRSGs) is built upon a diverse installed base of around a thousand steam generators. We tailor solutions to the unique needs of each customer and provide services ranging from changing operations and reducing emissions to preparing for the future, such as changing from natural gas to hydrogen as fuel. We offer our services for both NEM- and other OEM-made units, including inspections, replacements, performance improvements, and complete rejuvenation.

Why not significantly improve a good product? Our customers are increasingly focused on extending the service life and thus increasing the cost-effectiveness of their machines and equipment. In many sectors, hydraulic cylinders are subjected to very high mechanical and abrasive loads. This is particularly true for applications in potash and rock salt mining, underground and surface mining, quarries, the iron and steel industry, and power plants. These stresses are even present in offshore applications and the food industry. As a manufacturer and maintenance provider, we have made it our mission to further develop hydraulic cylinders for these applications, setting a new standard. In collaboration with leading experts in materials development, we have succeeded in achieving this goal. HTec hydraulic cylinders feature materials that combine new materials with a special surface coating. The HTec materials have been extensively researched and tested by RWTH Aachen University. A hardness of over 1700 Vickers (HV) has been confirmed. All coatings are extremely corrosion-resistant, and peeling or flaking is impossible. A further advantage is the materials' excellent sliding and emergency running properties, virtually eliminating cavitation, galling, and adhesion tendencies. In addition to their use in hydraulic cylinders, HTec material variants can also be used on many other components, such as bushings, bolts, and rollers, that are subject to increased stress. The right combination can be selected from the HTec family portfolio for every application.

aomation bietet Services rund um das Produkt HxGN EAM. Unser europäisches EAM-Expertenteam entwickelt erstklassige Enterprise Asset Management-Lösungen zur Optimierung ihrer Instandhaltungsprozesse und übernimmt die Verantwortung für die Umsetzung anspruchsvoller und innovativer EAM-Konzepte.

Instead of the usual internal mechanical control circuit and external control drive, the latest generation uses an external proportional valve to adjust the blade position. This has the advantage that the valve can also be replaced during operation without stopping the fan. The hydraulic blade adjustment of this generation has already been on the market for more than 10 years and is used with great success by more than 30 customers on over 80 machines. Through constant dialog with our customers, we have always been able to develop exactly the products that our customers need. Our engineers and technicians have repeatedly demonstrated great innovative strength.

As a certified PARKER distributor with HTC status, we supply and install products in the well-known PARKER quality. All other leading manufacturers are also available on request. We can offer you components from a wide range of standard products through to custom solutions for the realisation of your project. Tell us your requirements and we’ll be glad to advise you!